Tili Ota yhteyttä
Ostoskorisi
Black Weekjopa −30 %vielä 8 pv 04:42:09
Toimitus DPD & FedEx
Tarvitsetko apua? Kysy AI:lta

Reikäsaha yksittäinen Cimco 208814

Reikäsaha yksittäinen Cimco 208814
-13%
Black Week
Reikäsaha yksittäinen Cimco 208814
82,30 €
94,45 €−13 %
PDF
PDF
Varasto 3 Tuotekoodi 2353254 Malli 208814 Takuu 2 vuotta

Toimitus ja palautukset

Arvioitu toimitusaika maanantai 14. joulukuuta
Saat päivitykset yksityiskohtaisen seurantajärjestelmän kautta
Maksuvaihtoehdot
MaksukorttiVisaMastercardApple PayGoogle PayTilisiirto

Esitä kysymys – AI-avustaja vastaa heti.

Kuvaus

The Cimco 208814 hole saw is a single-piece cutting tool designed for making clean circular holes in a variety of masonry and mineral-based materials. With a diameter of 5.2 cm, this hole saw is suitable for creating openings for pipes, conduits, fittings and other installations in brick, concrete, lightweight concrete, plasterboard, stone and ceramic tile. The construction focuses on durability and cutting precision for repeatable results in professional and home-improvement tasks.

Advantages

This hole saw delivers accurate round cuts with reduced chipping on tile and stone and reliable penetration in porous materials. The single-piece design improves tool stability during drilling and simplifies mounting and removal. Its diameter offers a balance between reach and control, making it useful for both tight installation spaces and standard through-holes. The tool is compatible with common drill attachments and offers long service life when used with appropriate drilling technique and cooling where required.

Suitable for

Key specifications

How to use

Secure the hole saw to a compatible drill arbor and confirm the arbor fits the drill chuck. Mark the center of the intended hole on the work surface and, where possible, use a pilot bit or guide to keep the saw aligned. Begin drilling at low speed to establish the cut, then increase speed moderately while maintaining steady pressure. For dense masonry or tile, apply intermittent drilling and withdraw occasionally to remove debris and reduce heat buildup. When cutting tile, consider using backing or tape to reduce surface chipping and support the area outside the cut.

Recommendations

Use appropriate personal protective equipment (eye protection, gloves and dust mask) and select drill speed and feed pressure suitable for the material. For prolonged or repeated use in hard materials, use water cooling where practical and inspect the cutting edge regularly for wear. Ensure the workpiece is secured to prevent movement and follow the drill manufacturer's safety instructions when mounting and operating the tool.

Tärkeimmät ominaisuudet
  • Drilling openings for electrical conduit and plumbing in brick and concrete
  • Cutting penetrations for ventilation, cable glands, and fixtures in lightweight concrete and plasterboard
  • Creating holes in stone and ceramic tile when used with steady feed and suitable backing
  • General repair, retrofit and installation work in residential and commercial settings
  • Cutting diameter: 52 mm
  • Applicable materials: brick, concrete, lightweight concrete, plasterboard, stone, ceramic tile
  • Design: single-piece hole saw for direct attachment to compatible drill arbor
  • Intended use: through-hole cutting for pipes, conduits and fixtures

Tekniset tiedot

Tekniset tiedot
Halkaisija
52 mm
Osien määrä
1 pc(s)
Reikäsahojen määrä
1 pc(s)
Sopii
Pora
Sopii materiaaleille
Brick, Concrete, Lightweight concrete, Plasterboard, Stone, Tile
Tuotteen väri
Ruostumaton teräs
Työpituus
150 mm
Tyyppi
Yksittäinen
Hintahistoria viimeisen 6 kuukauden ajalta
Reikäsaha yksittäinen Cimco 208814
Nykyinen
82,30 €
Alin 7 pv
82,30 €
Ylin 7 pv
96,09 €
Muutos 24 h
-6,98 €   -8%
Muutos 7 pv
-6,12 €   -7%
Muutos 30 pv
-6,30 €   -7%

Kirjoita arvostelu

Arvosana *
Nimesi näytetään julkisesti – voit käyttää nimimerkkiä. Kutsumme ostajia kirjoittamaan arvosteluja; tarkistamme arvostelut ennen julkaisua ja julkaisemme myös kriittiset.

Lisää CIMCO-tuotteita tässä kategoriassa

11

Suositut tuotteet tässä kategoriassa

5
Myyjä: UAB KUR LT · Gariūnų g. 57-14, LT-02300 Vilna, Liettua · Yritystunnus 303192950 · ALV-numero LT100008198612 · Toimitus EU:sta (Liettua)
WhatsApp
Messenger
Hei, olen DistriNoden tekoälyavustaja. Autan sinua löytämään tuotteita, vertailemaan vaihtoehtoja, laatimaan tarjouksia PDF-muodossa tai tekemään tukipyyntöjä.
Kaikki kategoriat