GHIANT Lexan -spraymaali, valkoinen, nro 710, 400 ml

This ready-to-use, quick-drying, and fuel-resistant white Lexan spray paint is specially developed for painting polycarbonate RC car bodies. The special solvent etches the surface to allow the paint to bond permanently with the material. This lightweight paint offers the potential for up to 15 grams less weight on a 1/10 scale race body compared to pre-painted or water-based colored bodies, helping to lower the center of gravity. Delivered in a 400ml can, it is easy to apply in light coats at a spraying distance of 20 to 30 cm and is also ideal for backing fluorescent colors.

• White spray paint No. 710 for polycarbonate RC car bodies, 400 ml
• Specifications
• Hazard statements (H codes)
• H222: Extremely flammable aerosol.
• H229: Pressurized container: may burst if heated.
• H319: Causes serious eye irritation.
• H336: May cause drowsiness or dizziness.
• Precautionary statements (P codes)
• P210: Keep away from heat, hot surface, sparks, open flames and other ignition sources. No smoking.
• P251: Do not pierce or burn, even after use.
• P305 / P351 / P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337 / P313: IF eye irritation persists: Get medical advice/attention.
• P403 / P233: Store in a well-ventilated place. Keep container tightly closed.
• P410 / P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.
• Supplemental hazard information
• EUH066: Repeated exposure may cause skin dryness or cracking.

In the box

• 1× 400 ml spray paint

Before painting, remove dirt particles, cut out the body and sand the cut edges. Mask areas that are not to be painted with masking film or tape; make sure surfaces are dry and free of dust.

Many bodies have a transparent protective foil on the outside. Do not remove it until the paint has dried.

Paint dark colours before light colours to prevent the dark colours from showing through.

Shake the can vigorously for approx. 2 min. before use, until the mixing ball rattles. Spray from approx. 20–30 cm using even cross movements.

Covering capacity varies slightly by colour. Apply light coats to avoid bleeding; the final result takes 2–3 coats. Wait approx. 5 min. between coats rather than applying one heavy coat. Let the paint dry for 5 minutes before removing the masking film and applying the next coat.

After use, turn the can upside down and spray for 2 s until the nozzle is empty.

Fluorescent colours appear not to cover as well as normal colours. Apply only very light coats at temperatures above 15 °C, spraying from a distance of +/-15/20 cm.

Let fluorescent colour dry for 30 min., then back it with white RC Car Colour to obtain the fluorescent effect.

RC Car Colours in white is a paint for Lexan car bodies. The solvent etches the body surface so that the paint bonds permanently with the plastic. It remains elastic, even in a strong crash, and does not chip or scratch.

• Highlights
• Remains elastic
• Fuel resistant
• Technical data
• Hazard statements (H codes)
• H222: Extremely flammable aerosol.
• H229: Pressurized container: may burst if heated.
• H319: Causes serious eye irritation.
• H336: May cause drowsiness or dizziness.
• Precautionary statements (P codes)
• P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P251: Do not pierce or burn, even after use.
• P305 / P351 / P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337 / P313: If eye irritation persists: Get medical advice/attention.
• P403 / P233: Store in a well-ventilated place. Keep container tightly closed.
• P410 / P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.
• Supplemental hazard information
• EUH066: Repeated exposure may cause skin dryness or cracking.

In the box

• 1× Lexan paint white No. 710, 400 ml
• Notes

Remove any protective foil on the outside of the body only after painting; the body can be cut out beforehand.

Clean the body thoroughly with dish soap or brake cleaner and shake the can vigorously for about 2 min.

Spray the paint from a distance of 20–30 cm. When using multiple colours, start with the darkest, as dark colours can otherwise show through the light ones.

Apply several thin coats instead of one thick coat and wait about 5 min between sprays.

Wait at least 5 min before removing the protective film or masking film of the design.

After use, turn the can upside down and spray for about 2 s to empty the nozzle.

• Brand: Ghiant